Target terror wii iso manual#
Target terror wii iso software#
Target terror wii iso windows 8#
Target terror wii iso series#

It's worthless for anything more then data logging. If you thought the meter is slow on these units, wait to you see the software. On my unit, there is no icon displayed on the meter screen when connected. Make sure the meter is on and then click on 'turn on'.

Set the com port you're using to 1200, 7 bit, SPACE and 2 stop bits. In Device Manager open the LPT & Com port setup. From the scopeview program setup, select: com port, 1200 baud, and M38XX, save settings but leave open. None of this appears to be documented in the US docs and nothing but the cable and diskette come along with the accessory with nothing in the doc files except for meter usage. в‚¬50 (Conrad has it for в‚¬40) might be more than you're willing to spend, though.

Target terror wii iso windows 8#

Hooking up a scope to the TX line should show a signal if that's the case.ДЄnother program that looks like it would support the MS9150 and Windows 8 is, which looks like a low-end version of Labview. Skimming the source, it looks to me like the MS9160 would just output a continuous stream of results in ASCII format. Not sure if there's a Windows version available. Claims to support the MS9160, which might be compatible with the MS9150. I'm wondering if the db25-db-9 adapter flipped the tx/rx lines at this point. The polish docs mention selecting the metex 3850/3830 for the dos version, but nothing again for the windows scope view which has a parameter screen. There's no DOS version on this disk, just the Scopeview.

Target terror wii iso software#

From the polish docs, there's supposed to be an annunciator in the display once the software makes the connection.

There's nothing in the doc files even though the disk specifically is labeled that it's for the Tenma 72-5085 which is the 9150.

Target terror wii iso manual#

I did find a polish publication that mentioned the older dos version setup was 1200, 7 bit, 2 stop bits which my manual has absolutely nothing on computer interfacing for either the 9140 or 9150.

Target terror wii iso series#

I've tried all but the ME series meters and no joy. The software setup asks for the baud rate stop bits, etc and also asks you to choose from several Metex models, none of which are the 3640d. Still no communiction with the supplied DB-25-db-25 cable that came in the box with a 9 pin adapter. I have the v1.09 scopeview software up and running under an old laptop running win 98. I've seen data sheets with the 9150/9160 as co-products under the Unisource label dating to 2006 or 2007, not sure on that when I was trying to find a veneer drive replacement for one of the earlier MS-9140 units. This unit must have been manufactured after the 42 week of 2003 by latest date codes on some of the chips, well into XP dating. I did find an independent freeware Mscope that's supposed to work with some of the Metex meters and a V1.08 searching, but I'd like to find the last version. The Tenma72-5085 should be the full,standard version of the MS-9150 with the 4000 count DMM, 1.2 gig timer/counter with no differences unlike some of the other OEM versions that had reduced features and specs that looked just like it. I've seen Unisource handhelds shown packed with a CD during past years and wonder if that is a more updated product that will work with XP or later. Check the transmissions lines to the LCD with a scope. Metex Universal combined test instrument systems/stations. Go to the right automaker and a vehicle equipped with a manual transmission becomes more than just an entry-level loss-leader on compact cars. Does anyone know of what the latest software is and where to find it? The Metex.KR address doesn't seem to get any response if you write them or look at their website for any downloads or support. If they still make it with the DB25 RS-232, something must work with it. It apparently will not run under XP even these units I think are still available as the 9150/60 and the newer 9170, I can't find a hint of support for the software or if any of the latter Metex/Unisource or any of the jobbers such as MCM,Tenma,Elenco,Voltcraft,Conrad or anyone else that sold these has updated software that will work with this unit. I've got a MCM version of the Metex MS-9150 working again and the software diskette that came with cable kit was Scopeview V1.09 when it was purchased as an accessory kit from MCM.